French Harbor Town – Part IX

So finally I finished up the impetus for this project – the Brigade Games U Boat.

Being a gaming piece first and foremost I wanted it to be easy to store and transport, so decided to not go overboard (see what I did there) with the detail. I made the decision early on to leave it as a three piece affair and to magnetize as many pieces as possible.

The kit came with a single 20mm, the 8.8cm deck gun, two periscopes, an UZO pedestal and the posts for the railing at the aft of the conning tower. Surprisingly missing were the iconic (to me) horseshoe shaped life rings. I was able to find some 1/48th scale ones on Shapeways along with a more detailed UZO and a circular range finder.

Assembly of the guns was pretty straight forward, and I magnetized the bases of these along with the periscopes and the UZO. I then used some solder to create the aft railing. I affixed the life rings but decided to leave off the RF antenna. It was housed in a box and I didn’t want to sacrifice any more real estate in the conning tower as I wanted to cram some based figures in there.

After that it was a matter of firing up the airbrush and giving it a coat of paint. The markings are hand painted and are my interpretation of the U-201 coat of arms and snowmen.

Additionally I scabbed together a couple of gangplanks from basswood strips. The rubber dinghy is from Bandai and the supplies are from the scrap box.

Finally I’ll put the finishing touches on the figures for the orders of battle and gin up a few play aids.

Late War Waffen SS Grenadiers – Part I

At this year’s Historicon I’ll be running two WWII skirmish games using Disposable Heroes II. One scenario is a late war engagement between elements of the US 90th Infantry Division and the 2nd and 3rd SS Divisions.

As I dare not run a convention game with incomplete miniatures, I’m using this as an opportunity to finish my SS platoon that has been in various stages of completion for many years. I’ll be documenting my progress and camouflage painting techniques in a series of posts. This first installment will address the platoon composition, and the figures I have chosen to represent the soldiers/equipment.

I’m using two sources for my order of battle – the German Army book ANGRIFF! from Iron Ivan Games, and the late war German Grenadier list from the Chain of Command rulebook. Here’s my planned unit:

Grenadier Platoon

• Platoon HQ
  • Lieutenant w/MP-40 – Warlord
  • Staff Sergeant w/MP-40 – Warlord
  • Private w/Kar-98k – Warlord
  • Private w/Kar-98k – Victory Force
  • Private w/Kar-98k – Victory Force
• 1st Squad
  • LMG Team
    • Sergeant w/MP-40 – Victory Force
    • LMG Gunner w/MG-42 – Warlord
    • LMG Loader w/Kar-98k – Warlord
    • Ammunition Bearer w/Kar-98k – Warlord
    • Private w/Kar-98k – Warlord
  • LMG Team
    • Corporal w/Kar-98k – Victory Force
    • LMG Gunner – Warlord
    • LMG Loader w/Kar-98k – Warlord
    • Ammunition Bearer w/Kar-98k – Victory Force
    • Private w/Kar-98k – Warlord
• 2nd Squad
  • LMG Team
    • Sergeant w/MP-40 – Victory Force
    • LMG Gunner w/MG-42 – Warlord
    • LMG Loader w/Kar-98k – Warlord
    • Ammunition Bearer w/Kar-98k – Warlord
    • Private w/Kar-98k – Warlord
  • LMG Team
    • Corporal w/Kar-98k – Victory Force
    • LMG Gunner – Warlord
    • LMG Loader w/Kar-98k – Warlord
    • Ammunition Bearer w/Kar-98k – Victory Force
    • Private w/Kar-98k – Warlord
• 3rd Squad
  • LMG Team
    • Sergeant w/MP-40 – Warlord
    • LMG Gunner w/MG-42 – Renegade Miniatures
    • LMG Loader w/Kar-98k – Warlord
    • Ammunition Bearer w/Kar-98k – Warlord
    • Private w/Kar-98k – Warlord
  • LMG Team
    • Corporal w/Kar-98k – Victory Force
    • LMG Gunner – Renegade Miniatures
    • LMG Loader w/Kar-98k – Warlord
    • Ammunition Bearer w/Kar-98k – Warlord
    • Private w/Kar-98k – Warlord

Platoon Support

• Sniper Team
  • Sniper w/Scoped Kar-98k – Warlord
  • Spotter w/Kar-98k – Warlord
• Panzerschreck Team
  • Gunner w/Panzerschreck – Warlord
  • Loader w/Kar-98k – Warlord
• Flamethrower Team
  • Gunner w/Flamethrower – Warlord
  • Assistant w/Kar-98k – Warlord
  • Private w/Kar-98k – Warlord
• Recon Team
  • Sergeant w/MP-40 – Warlord
  • LMG Gunner w/MG-42 – Warlord
  • LMG Loader w/Kar-98k – Warlord
  • Private w/Kar-98k – Warlord
• MG-42 HMG
  • Sergeant w/MP-40 – Warlord
  • HMG Gunner w/MG-42 – Warlord
  • HMG Loader w/Kar-98k – Warlord
• Forward Observer
  • Radioman w/Kar-98k – Warlord
• Medic
  • Medic – Warlord
• 7.5cm le IG.18
  • le IG.18 w/3 Crew – Warlord
• 7.5cm Pak 40
  • Pak 40 w/3 Crew – Crusader

I’ll also be adding in some various figures with panzerfausts and pioneer equipment.

Sarissa Precision Radar Station Build

After reading these posts on the Too Fat Lardies blog here and here, I decided to take some inspiration (steal ideas) and build my Sarissa Radar Station. Here’s what I came up with.

The Lardies mounted their station on a hexagonal base that was made of carved foam. Knowing how bad I am with foam work, I decided to design my base using Tinkercad and print it using my Printrbot Play. It’s hard to see in this picture, but this print has some very bad horizontal banding (for those that know anything about 3D printing it was caused by a sinusoidal heat fluctuation in the hot end) however it ended up being a happy accident as it kinda gives the effect of marks left by a concrete form.

I mounted the hex to a rectangular base and covered the horizontal surfaces with sand.

Prior to assembly, I traced the outer ring of the dish and the roof of the shack onto some card stock to use to cover the seams where some of the parts join.

Construction of the building was straight forward. Before adding the roof, I painted the interior and added a map, propaganda poster and a calendar to the walls. In hindsight this was a waste as you really can’t see into the building.

After the framework of the dish was built I added some mesh using some sort of nylon that probably came from a bag of mints from a wedding. I don’t know what it’s called, but the material is pretty common.

To complete the dish I glued some styrene strips along the interior frames and capped the outside with the trimmed card stock ring.

Before mounting the building I wanted to finish the base so I added a few things from the parts bin – a box, drum and a bicycle from Dixon.

Here are a few shots of the finished base.

And here’s the finished piece. The voltage warning signs are printed images from online, mounted on the scrap pieces that came out of the window panes and the railing is a bent paperclip (both ideas stolen from the Lardies). The steps are from Grandt Line.

This was a fun little build of a unique subject and I’m really happy with the results. I’d highly recommend the Sarissa kit if you’re in the market for an interesting objective.

Rubicon Sherman Build Part IV – Finishing

Recently Fall hit and the humidity dropped considerably, so I was able to get out the airbrush and finish up the Rubicon Sherman.

I began by brush priming the metal parts with Gunze Sangyo Mr. Metal Primer. I then primed the entire model with AK Interactive Grey Primer, shot straight from the bottle through an Iwata Eclipse HP-CS  at ~18 psi. The AK Interactive primer is, by far, my favorite. It binds, coats and levels better than any other primer, acrylic or otherwise, that I’ve used.

Primed Rubicon (Right) and JTFM (Left) Shermans

Once dry I pre-shaded the model with Vallejo Model Air #43, Olive Drab, thinned at 3 parts paint to one part Liquitex Airbrush Medium, one part Vallejo Airbrush Thinner and one part Vallejo Satin Varnish shot at ~15 psi. In hindsight, I probably could have gone with a darker shade here.

Pre-Shading

Next I applied a base coat of Vallejo Model Air #44, Light Grey Green thinned as above.

Base Coat

After the base colors had set completely I applied the markings. The turret stars are from Archer Fine Transfers, the differential dashed circle star is from I-94 Enterprises and the serial numbers are from the kit sheet. I then brush painted over the turret stars with Vallejo Model Color #889, US Olive Drab.

Turret Star and Serial Number

Differential Cover Star

Overpainted Turret Star

Post-markings I added some shadows using a thin wash of MIG Productions 502 Abteilung Wash Brown oil paint. This was followed by highlighting with some light dry-brushing of Vallejo Panzer Aces #322, US Tanker Highlight.

Shadow Wash

Dry-brushed Highlights

Following this I painted the remaining accessories and details with various Vallejo Acrylic and Humbrol Metal Cote paints.

Air Recognition Panel and Tools

Rear Stowage

Headlights and Hull MG

Turret Stowage

Tank Commander

I then started working on the tracks, bogie wheels and return rollers. The bogies and return rollers were painted with Vallejo Panzer Aces #306, Dark Rubber, given a wash of acrylic black, and lightly dry-brushed with Vallejo Panzer Aces #305, Light Rubber. The tracks were painted with Vallejo Panzer Aces #304, Track Primer given a wash of acrylic black, and lightly dry-brushed with Vallejo Panzer Aces #305, Light Rubber. Earlier on in the build I had mentioned that I believed the tracks we’re supposed to be the steel chevron type, but because of the ambiguity I chose the easier route, for me, and painted them as rubber. The track end connectors were given a wash of True-Earth Burnt Rust R. Once this was dry I painted the raised details of the end connectors with Humbrol Metal Cote Aluminum. These metal cote paints dry to a matt black and then can be buffed. I used my finger and a micro-brush to gently buff the end connectors.

End Connectors With Rust

End Connectors Post-Buffing

Once the tracks were complete I started weathering the kit. In trying to keep it moderate, I started with an overall thin wash of MIG Productions 502 Abteilung Light Mud and then added some subtle vertical streaking with MIG Productions 502 Abteilung Engine Grease. I then added some staining around the filler caps with AK Interactive Fuel Stains.

Fuel Stains

After the oils and enamels were dry I started to weather the lower hull using a product that was new to me – Mud-in-a-Pot from Reality in Scale. Mud-in-a-Pot is an acrylic based textured mud that can be used straight from the jar. I used a lighter shade on the majority of the lower hull, and used the darkest shade closer in towards the running gear. I really like this product, but need to spend some more time with it to fully realize its potential.

Mud-in-a-Pot

Then when the “mud’ had dried (exceptionally hard by the way) I attached the tracks to the lower hull. This was followed by a light application of some MIG Pigments to harmonize the mud colors.

Tracks and Pigments Applied

As a final touch I gave the tank commander a map and a pair of binoculars from the scrap box.

Turret Details

To finish the kit off, I sprayed the entire model with AK Interactive Matt Varnish. Here are a few photos of the finished kit, and some pics alongside a JTFM Sherman that I built in parallel.

To summarize, the Rubicon Sherman is an excellent kit that was a really fun build. If you’re looking for Shermans to add to your arsenal, I highly recommend this model. I will certainly be checking out their other offerings in the near future.

Pros

• Easy Assembly
• Clear Instructions
• Provides Multiple Main Gun Choices
• Plastic – My Favorite Medium
• Excellent Detail
• Good Part Fit
• One Piece Tracks

Cons

• No Marking Guide
• Decals Slightly Thick
• Track “Identity Crisis”
• Lack of Extra Turret Ring

Rubicon Sherman Build Part III – Final Assembly

I was going to break this up into two parts, but the rest of the assembly went so fast I decided on a combined post.

The tracks and suspension for the Rubicon Sherman consist of five parts; the tracks and outside suspension/bogies, three inner bogie assembly halves and an inner drive sprocket piece. The assembly of these was straight forward. I sanded the seam along the part of the tracks that would be visible, and then glued the inner parts to the outer track/suspension assembly. While I understand the need to simplify the suspension, especially for a wargaming model, the design did result in a visible seam in all of the bogies. I decided to not fill these as the difficulty of sanding them didn’t seem worth the effort. Also of note, the track pattern is greatly simplified as well. I believe that they are supposed to be the steel chevron type, but I am unsure.

Outer Track Assembly

Tread Pattern

Track and Suspension Parts

Bogie Seams

I set the track assemblies aside and began working on the lower hull. The lower hull is split into two pieces, and Rubicon cleverly hid any visible seam by incorporating it into the engine doors and hiding it with the trailer hitch.

The Lower Hull

Engine Doors and Trailer Hitch

I like my wargaming models to have a little heft and wanted to add some weight to the hull. I affixed some Pinewood Derby Chassis Weights using CA glue.

Lower Hull Weights

I then attached the idler wheel assemblies.

Idler Wheel Assembly

The next step was attaching the differential cover to the lower front of the hull. I dry fitted this piece with the upper hull, and discovered it was going to take a little coaxing to fit correctly. I cemented it, strapped it down with some rubber bands and let it dry overnight.

Differential Cover

Like the turret, the differential cover was a cast piece. I applied the same technique as I did with the turret to try and give it that texture.

Differential Cover Texture

The bulk of the upper hull is one piece that fit perfectly on to the lower hull.

Upper Hull

The next steps called for attaching the rest of the upper hull parts – headlights, exhaust deflector, hull MG, etc. These parts went on without issue. During these steps I drilled out the front and rear hull lift hooks.

Front Lift Hooks

To finish off the kit I added the Culin hedgerow cutter and some stowage. The Culin device had some clear injector pin marks that I tried to fill with putty. I plan on covering up my poor work with some weathering.

Injector Pin Marks

Culin Device Attached

As the kit did not include any stowage, I added some from the space parts bin.

Stowage

As a final step, I made an air recognition panel using foil from a wine label (no shortage of this material at the Emmett Estate), some painter’s tape and thread. After I affixed it to the tank I brush painted it with matt medium to stiffen it up.

Air Recognition Panel

Panel Attached

Next in Part IV I’ll begin painting and applying the markings.